65GS.com - Buick Gran Sport Enthusiasts!
General Discussion => General Discussion => Topic started by: GranSportSedan on October 24, 2018, 09:11:05 AM
-
I have found a very nice all original 66 Special to replace my destroyed 66 GS. the GS was a non A/C car and the Special is a 300 powered car with factory A/C. I am considering swapping all the GS stuff including engine and trans to the special and was wondering if there is anything on a 66 GS with A/C that is specific to the GS only. in other words will all the A/C components aside from compressor mounting brackets work with the nailhead conversion? is the condenser different? i'm seriously thinking of swapping the entire frame and drivetrain. i can have it all detailed and then just mount the special body on the new chassis. thoughts?
-
The hoses that connect to the compressor and the two brackets supporting them are different I think the hose assemblies are close enough though that you could tweak the bends a littler or have them modified by classic auto air in FL to fit if you are not worried about them looking exactly correct. Also keep in mind that the compressor on a 401 has a double groove pulley, and the special compressor has a single. The compressor itself is the same--just has different pulley and a clutch plate with a longer snout on it. The compressor and bracket setup is common with all the 64-66 nailhead powered wildcats/electras/rivs, so you are not limited to finding parts from a Skylark GS.
Parts you will need to find:
3 groove crank and wp pulleys
2 groove A/C compressor and brackets from nailhead engine
2-groove alternator pulley
Clutch fan from 64-66 nailhead engine
Radiator for a Skylark GS with A/C and the different top radiator hose
Fuel filter with return line connection (only on A/C cars)
-
And I think what you are proposing is a great idea! I wouldn't hesitate to tackle swapping the Special body onto your GS chasis. Even if you don't have all the A/C stuff in hand, you can always add that stuff on later as you find it and enjoy the car in the meantime.
-
Great summary Brian. I would add that the fan shrouds are different (my one-track mind at work again...). They are also different than the shrouds on the big cars, so exclusive to the 65-66 Skylark GS. There are some repops available, but originals seem to be non-existent.
Good luck with the swap!
:cheers2:
Chuck
-
Good catch Chuck! I wasn't even thinking about the fan shroud. That too is one of the items that can be added later and not essential for driving the car.
I am always a big proponent of working with what you have to get a car going, then working out the last 5% of the details later on once the parts are found!
-
Thanks for the input fellas. I was aware of the fan shroud but not the dual pulley issue. I think I can source most of the parts fairly easily. I had all the parts to repair my GS but then found that the seller also failed to disclose the paper thin floor pans from front to rear and I decided at that point I was either going to scrap the car and part it out or find a nice Skylark or Special and do a major Organ transplant.
I just love the interior on the Special
-
when I say all original I really mean it. still has all the Cali smog equipment. it was a California high desert car and it has been in storage for at least 10 years.
-
I like it too! Especially the center arm rest!
-
GranSportSedan
WOW
Almost all my 64-65 Buick A bodies have had white or red interiors but I have never owned a 66.
Your red interior is amazing.
Could you post a picture with the arm rest folded down that Brian was talking about?
From the pictures it looks like the narrow bands in the seats are a little darker then the wider ones.
I also hadn't seen the 66 California smog setup. Thanks for the documentation.
Milton
-
Dear Bob, Brian, Milton, and mid-60s Buick owners with long memories, . . . .
when I say all original I really mean it. still has all the Cali smog equipment. it was a California high desert car and it has been in storage for at least 10 years.
I also hadn't seen the 66 California smog setup. Thanks for the documentation.
Yup, I can spot one of those crankcase ventilator hoses from a good distance away. My trusty wagon has limped with one of those since birth until she got her "supersized" engine in 2013. Can you believe it, she has never complained about losing it!! . . . . :laughing7:
Cheers, Edouard :occasion14:
-
Yup, I can spot one of those crankcase ventilator hoses from a good distance away. My trusty wagon has limped with one of those since birth until she got her "supersized" engine in 2013
I wonder if the old smog systems cost the engine some power vs an identical engine without the smog stuff.
-
Dear Bob and mid-60s Buick owners seeking maximum power,
I wonder if the old smog systems cost the engine some power vs an identical engine without the smog stuff.
Those hoses were part of a crankcase ventilation system. They were pulling exhaust out of the crankcase and forcing the engine to burn it a second time to reduce the exhaust emissions. Recirculating exhaust can't do anything but reduce performance. Most performance engines instead have a crankcase breather to allow any gas pressure to escape to the atmosphere. The only real reason to keep that early pollution control technology is to keep the car absolutely original. It isn't like that early technology was doing much to reduce the pollution and none of us drive our cars all that much anyway.
Cheers, Edouard :occasion14:
-
Dear Bob and mid-60s Buick owners seeking maximum power,
I wonder if the old smog systems cost the engine some power vs an identical engine without the smog stuff.
Those hoses were part of a crankcase ventilation system. They were pulling exhaust out of the crankcase and forcing the engine to burn it a second time to reduce the exhaust emissions. Recirculating exhaust can't do anything but reduce performance. Most performance engines instead have a crankcase breather to allow any gas pressure to escape to the atmosphere. The only real reason to keep that early pollution control technology is to keep the car absolutely original. It isn't like that early technology was doing much to reduce the pollution and none of us drive our cars all that much anyway.
Cheers, Edouard :occasion14:
back then wasn't it just and air pump that pumped fresh air into the exhaust to dilute the exhaust gases so that it would pass Emissions? Then there was the closed crankcase system that was hooked to the breather to the valve cover so that any vapor form the engine was sucked into the carb. Egr (exhaust Gas Recerculation) came about latter mid early 70's, right?
-
The later EGR systems were the ones that brought exhaust gas back into the intake tract. Early 1970's. It's purpose is to lower combustion temperatures to reduce N2O emissions.
The PCV will recycle most crankcase gasses (blow by) back into the intake. Suppose those gasses could be considered to be comprised of 'exhaust'. The open PCV (with open breather) will vent any excess blowby to atmosphere, whereas the closed PCV will try to capture the excess and route it to the air cleaner.
For 1966, they added the smog pump which will use some engine power to drive. It injects air into the exhaust to allow unburnt fuel to continue burning.
Bob, the 4 bbl '66 Carbs with Calif smog systems did have smaller primary venturi's......I'll guess that reduces the cfm, and horsepower.
As for the GS AC compressor, I have one from a '66 Riv GS and the label, IIRC, Says it's for the GS's.
-
Here's a well-worn twin to (is it yours yet?) white/red Special:
https://www.ebay.com/itm/1966-Buick-Skylark-Special-Deluxe-V8/253947507236?hash=item3b20737224:g:idcAAOSwSYpbz-Jg:rk:11:pf:0&vxp=mtr (https://www.ebay.com/itm/1966-Buick-Skylark-Special-Deluxe-V8/253947507236?hash=item3b20737224:g:idcAAOSwSYpbz-Jg:rk:11:pf:0&vxp=mtr)
Looks solid, but not nearly as nice as your appears to be.
Good to hear you found something to put that B262 on!
-
Here's a well-worn twin to (is it yours yet?) white/red Special:
https://www.ebay.com/itm/1966-Buick-Skylark-Special-Deluxe-V8/253947507236?hash=item3b20737224:g:idcAAOSwSYpbz-Jg:rk:11:pf:0&vxp=mtr (https://www.ebay.com/itm/1966-Buick-Skylark-Special-Deluxe-V8/253947507236?hash=item3b20737224:g:idcAAOSwSYpbz-Jg:rk:11:pf:0&vxp=mtr)
Looks solid, but not nearly as nice as your appears to be.
Good to hear you found something to put that B262 on!
wow, when brand new that car would have been a twin to the one I picked up. mine appears to be a little less used..lol
as far as that $300 B262 goes. I didnt want it to use as I have a factory dual quad setup and i'm not looking to set the world on fire. I saw what a screaming good deal it was and knew I could turn it for at least $1000 profit. however I just couldnt do that in good conscience and thats why I informed the seller that he was waaaay low on the price. I privately pm'd him again and told him why I was not going to purchase the intake from him and strongly urged him to relist it on Ebay or at least raise the price to $700-800. I'm hoping thats what he did. after all it's been many years since you could buy a B262 for $300 and now they are going for $1500-1800.
-
He was way too high on those GS exhaust manifolds at $800. And too low on the B262 at $300. I thought maybe he had the prices inadvertently switched. Good of you to set him straight on the intake.
I scored an iron 2x4 intake on eBay this summer for $235. But I don't think that makes me a bad guy, just lucky!
-
I scored an iron 2x4 intake on eBay this summer for $235. But I don't think that makes me a bad guy, just lucky!
if i had scored that B262 for $300 on Ebay that would have been a whole different thing. nothing wrong with that scenario. I bought a 66 Q-Jet intake locally for $275 from a Buick shop. he had two of them. then again I paid $400 for a NOS 66 425 Q-jet on Ebay.
-
got some new shoes on the 66 today and what a difference it makes. my plan is to use the GS frame and build the rolling chassis while leaving the Special in one piece and drivable until it's time to install the body.
-
Looks like a nice car!
-
Looks like a nice car!
It's a rust free solid car. The only drawback is it's an A/C car. I will make it work.
-
I like it! How's the interior?
Buick did a nice job on the trim of the 66 Special Deluxe. That side spear adds just the right amount of chrome.
My Special still has the 300 but I added a 5 speed and brake/suspension upgrades. It's a fun car.
-
I like it! How's the interior?
Buick did a nice job on the trim of the 66 Special Deluxe. That side spear adds just the right amount of chrome.
My Special still has the 300 but I added a 5 speed and brake/suspension upgrades. It's a fun car.
The interior is in very nice shape and probably one of the nicest things about the car other than the fact that there's no rust. Your car looks great Walt.
-
Walt,
I see you have 15's on the back of your special. what size tires? the rear wheels on my car are 15x8 but the extra inch was added to the inside and the tires are 255's and are pretty close to the wheel opening lips. I suppose my car has the later 66 rear which is wider.
-
255/60-15's on 15 x 7 wheels. Wheels have 4-3/8" backspace and 3-5/8" 'frontspace', so the 7" wheels are 8" wide edge-edge. Stock rear.
235/60-15 on the front.
I did roll the fender lip a little, or actually bent up maybe 1/2" of the lip on the inside. I just used pliers or vice grips, bending maybe 10 degrees at a time, going back and forth along the length until the bend was over 75 degrees, then finished off with a hammer and dolly. It's not hard, just do a little at a time. I have 255's on my red 66 too. Tire clearance is tight on one side since axle isn't perfectly centered in the body. Tough to make more tire clearance in a GS unless you cut the stainless ww trim.